← RC Hobby
RC Hobby

Cuorantine

A park flyer you can build yourself, with free plans.

The Cuorantine is a radio-controlled park flyer designed and built from scratch in April 2020. Its name is a nod to the quarantine that kept everyone at home that spring. Made from Depron foam, it was designed to be quick and easy to build and smooth to fly, for relaxed flying. The plans are free to download on this page, and the whole process, from plan to first flight, is shown in one video on the Hobby Share YouTube channel.

Highlights

01

Free plans

The plans and instructions are shared for free, ready to download from this page.

02

Light and simple

120 cm of wingspan and just 290 g ready to fly, controlled with rudder, elevator and throttle.

03

From plan to flight

One video shows the whole build step by step and ends with the flight. A second video, Cuorantine Acro, followed in May 2020.

In flight

A short clip of the Cuorantine flying over the hills.

Plans and downloads

Everything needed to build the Cuorantine, free to download. The plan sheets are in A4, ready to print at home. Download everything in one ZIP file, or pick individual files.

Materials

The complete list of what was used to build and fly the Cuorantine.

Airframe

  • 2 mm Depron, 840 × 700 mm
  • 5 mm Depron, 1000 × 400 mm
  • 2 mm balsa, 700 × 20 mm
  • 4 mm lite ply, 40 × 40 mm (firewall)
  • 4 mm round wooden dowel, 80 mm (a skewer works)

Power and radio

  • 50 W electric motor (a Multiplex BL-X 22-18 was used)
  • Cross motor mount and 4 small screws
  • 9×3.8 APC Slow Fly propeller with adaptor
  • 15–25 A speed controller
  • 400 mAh 7.4 V LiPo battery and charger
  • 2 servos of 9 g
  • Receiver and transmitter with 3 or more channels

Linkages and fixings

  • 2 small control horns
  • 2 small pushrod connectors
  • 2 pushrods of 45 cm
  • 40 cm of plastic sleeve
  • 5 rubber bands, 60 mm long (5 × 2 mm section)
  • Velcro and/or double-sided tape
  • Packing tape, paper tape and regular adhesive tape

Tools

  • Metal ruler, 50 cm (100 cm is better for some parts)
  • Metal saw, to cut the lite ply firewall
  • Scissors and craft knife
  • Sanding bar and sandpaper (coarse and fine)
  • Hot glue gun and glue sticks
  • Pliers, for the Z-bends on the pushrods
  • The free plans, printed in A4

With this setup, flights of around 15 minutes are usual when cruising at less than half throttle. The motor has enough power to loop from level flight and to climb to altitude in about a minute. The model is hand launched with the motor off, which is then switched on.

Frequently asked questions

What is Depron?

Depron is extruded polystyrene foam, normally sold in 1000 × 700 mm sheets in several thicknesses.

Where can Depron be bought?

It is usually available at hobby shops, office supply shops and DIY shops. A quick online search should help.

How much does it cost?

When the plans were published in 2020, the average price was 4 to 6 euros per sheet.

Can a bigger or smaller motor be used?

Yes. A 50 W motor is the suggested balanced option. Other sizes were not tested, but going under 35 W is not advised for performance reasons, nor over 80 W for structural reasons, because of the higher speeds and G forces.

Which propeller should be used?

For the park flying and cruising style the model was designed for, it depends on the motor and battery. The suggestion is the biggest diameter and lowest pitch that the motor and battery combination can handle.

Can a bigger or smaller battery be used?

Yes, but a bigger battery weighs more, so the model flies faster and puts higher loads on the structure. It is a compromise between flight time and weight. The designer prefers three 400 mAh batteries, swapped every 15 minutes or so, to one 1200 mAh battery, and suggests keeping the weight low.

What is the maximum weight of the model?

It depends on many variables, but going over 380 g is not advised. Around 280 g is a good compromise between low flying speed and the ability to handle wind.

Can bigger servos be used?

They can, but it is not recommended, because they add a lot of weight. 9 g servos are the right choice.

Can another type of glue be used?

Yes, any glue that is not solvent based: white glue, aliphatic resin, epoxy and foam-safe CA are some options. Except for CA, all of them add a lot of build time because of drying.

Checklists

Three short checklists for a safe flying session.

01

Before leaving home

  1. Inspect the wing
  2. Check the wing tips are secured in flight position
  3. Inspect the fuselage
  4. Inspect servos, control cables and horns
  5. Check the radio battery charge
  6. Check the motor battery charge
02

Before each flight

  1. Radio on
  2. Confirm the radio battery is OK
  3. Throttle stick at idle
  4. Check the propeller area is clear
  5. Connect the motor battery
  6. Check the condition of the wing rubber bands
  7. Check the control surfaces move correctly
  8. Confirm the propeller area is clear
  9. Do a quick motor test
03

After landing

  1. Disconnect the motor battery
  2. Radio off
  3. Check the motor, battery and speed controller temperatures, and investigate anything abnormal
  4. After the last flight of the day, store the rubber bands in a closed container with talcum powder to make them last longer

Build one

If you build a Cuorantine, share your photos, videos and modifications in the Cuorantine thread of the scratch building forum on RC Universe. Comments and suggestions for improvements are welcome too.

Safety note: building this model involves cutting tools. If you are not used to working with them, ask an experienced person for help. You build and fly the model at your own risk.

Details

Wingspan120 cm
Flying weight290 g
MaterialDepron foam
ControlsRudder · Elevator · Throttle